2021 Inspection Results -

Repair details are on the bottom of this page below the overview. 

If you have questions about repairs please save them for Tuesday at the Repair Tent.

Car No. = R500,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R501,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 17. "Kingpins, AASBD issued kingpins and bushings only".   Reason -> king pin too short

Car No. = R502,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 29. "Kingpins, 3-1/2" or 3-1/4" inch grade 8 and must be visible".   Reason -> too short (nut not flush0
• Failed item 32. "Bolts, 5/16 inch bolts".   Reason -> Cut bolts. remove if not used

Car No. = R503,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R504,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R505,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 15. "Axle Mounting Plates, AASBD issued. AASBD logo must be visible".   Reason -> rear axle does not meet 3
• Failed item 17. "Kingpins, AASBD issued kingpins and bushings only".   Reason -> front king pin nut flush with nuts
• Failed item 23. "Brake Pedal, 3/4 inch plywood or pivot style brake".   Reason -> pull back plate nut - not flush with stud

Car No. = R506,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R507,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 24. "Brake Facing, New AASBD brake pad installed".   Reason -> need brake pad

Car No. = R508,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 23. "Brake Pedal, 3/4 inch plywood or pivot style brake".   Reason -> fix brake pedal (seized)
• Failed item 26. "Foot Brace, Required 3/4x3/4x3 inch minimum size".   Reason -> cut bolt on foot brace
• Failed item 32. "Bolts, 5/16 inch bolts".   Reason -> cut bolts

Car No. = R509,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R510,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 15. "Axle Mounting Plates, AASBD issued. AASBD logo must be visible".   Reason -> rear axle does not meet 3" rule

Car No. = R511,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R512,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R513,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R514,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R515,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R516,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R517,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 19. "Alternate Rear Axle Mounting Assembly, Installed w/carriage or hex bolts and nuts AASBD issued".   Reason -> rear axle over 3"

Car No. = R518,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R519,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 9. "Hinge, AASBD issued".   Reason -> file bolts
• Failed item 29. "Kingpins, 3-1/2" or 3-1/4" inch grade 8 and must be visible".   Reason -> nut must be flush

Car No. = R520,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 6. "Helmet Width, Cannot change shape of helmet when put into headrest;7-1/4 inches outside between rivits".   Reason -> not 7
• Failed item 9. "Hinge, AASBD issued".   Reason -> file bolts
• Failed item 29. "Kingpins, 3-1/2" or 3-1/4" inch grade 8 and must be visible".   Reason -> nut not flush on front

Car No. = R522,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 15. "Axle Mounting Plates, AASBD issued. AASBD logo must be visible".   Reason -> RR axle does not meet 3

Car No. = R523,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R524,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R525,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason
• Failed item 15. "Axle Mounting Plates, AASBD issued. AASBD logo must be visible".   Reason -> does not meet 3" rule
• Failed item 17. "Kingpins, AASBD issued kingpins and bushings only".   Reason -> nut not flush
• Failed item 32. "Bolts, 5/16 inch bolts".   Reason -> fix weights pass plate

Car No. = R527,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R528,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R529,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 15. "Axle Mounting Plates, AASBD issued. AASBD logo must be visible".   Reason -> front axle does not meet 3"
• Failed item 41. "Errors in Construction, Repairs must be completed within one hour (Enter Repair Time)".   Reason -> foot brace must be bolted through floor

Car No. = R530,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R531,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R532,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 8. "Shell Cutout, Sides of shell must be padded with 3/8 inch thick foam".   Reason -> need helmet foam no clear tape allowed
• Failed item 9. "Hinge, AASBD issued".   Reason -> cut bolts & replace hinge
• Failed item 20. "Attachments, Cable clamps & eyebolts must be visible at axle without removal of any parts".   Reason -> Cable wrap incorrect

Car No. = R533,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 19. "Alternate Rear Axle Mounting Assembly, Installed w/carriage or hex bolts and nuts AASBD issued".   Reason -> rear axle too long
• Failed item 23. "Brake Pedal, 3/4 inch plywood or pivot style brake".   Reason -> axle stop bolts need cut

Car No. = R534,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R535,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R536,    Rally,    Master    VIP   But the following will be checked after shell installation

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!

Car No. = R538,    Rally,    Master    NON VIP

• item 2. "Nose Height, 8-1/2 inches high, 4-1/2 inches back minimum".   Reason -> Check after body installed !!
• Failed item 24. "Brake Facing, New AASBD brake pad installed".   Reason -> need pads
• Failed item 32. "Bolts, 5/16 inch bolts".   Reason -> cut bolts
• Failed item 33. "Adjustable, 10 pounds minimum (with wing nuts)".   Reason -> center weights